Recent Updates
- Which Industries Does Tapered Bit Apply To?top hammer drilling bits are drilling tools widely used in geological exploration, mining, construction and other industries. They utilize the power and impact of tophammer drilling to efficiently penetrate a variety of materials. This article aims to answer several key questions to gain insight into the characteristics and applications of tophammer drill bits.What is the working principle of a...0 Comments 0 Shares 584 ViewsPlease log in to like, share and comment!
- Preparing For Water Well Drilling Tools To StartPreparations before start-up1. The new rock drill is coated with anti-rust oil with high viscosity, which must be disassembled and cleaned before use. During reassembly, lubricating oil should be applied to the surface of each moving part. After installation, connect the safe drilling tools to the compressed air line, run with a small wind, and check whether the operation is normal.2. Inject...0 Comments 0 Shares 671 Views
- Dth Drilling Tools Good PracticeCreate good working conditions for dth drilling tools (1) Diamond is brittle and easily broken under impact load, so it is required to clean the inside of the hole, the bottom of the hole to be flat, and the diameter of the hole to be regular. (2) If it is found that there are cemented carbide chips, tire block chips, fallen diamond particles, metal chips, falling cores, falling...0 Comments 0 Shares 660 Views
- Introduction Of High Air Pressure Dth Drill Bits Loading And UnloadingWhether the well drilling tools can meet the requirements of the project is not only to control the production process of the drill pipe, but also to do a good job in the transportation and loading and unloading of the drill pipe. 1. Before unloading the drill pipe, make sure that the protective wire is tightened as it is....0 Comments 0 Shares 599 Views
- Dth Hammer Suppliers Product Life Extension IntroductionBecause the advantageous performance of diamond drill bits is incomparable with other similar products, diamond drill bits directly supplied by manufacturers can be widely used in the fields of exploration and mining, as well as in the field of infrastructure engineering. So how should users extend the service life of dth drill pipe suppliers' diamond drill bits to make them more...0 Comments 0 Shares 656 Views
- How To Use Sandvik Shank AdaptersSandvik Shank Adapters is a steel pipe with a ribbed tail, which is used to connect the surface equipment of the drilling rig and the drilling and grinding equipment or bottom hole device at the bottom of the well. The purpose of the drill pipe is to transport the drilling mud to the drill bit and raise, lower or rotate the bottom hole device together with the drill bit. The drill pipe...0 Comments 0 Shares 674 Views
- Confirmation Of The Use Environment Of Tapered Bit SuppliersVibration hammer must first determine the use environment Tapered Bit suppliers vibrating hammers are more dangerous, so protect them when you use them. The vibratory hammer has the characteristics of strong filling force, good pile sinking quality, sturdiness and durability, few failures, convenient use, strong power adaptability, and low noise. So what matters should the staff pay...0 Comments 0 Shares 717 Views
- How Reaming Bit WorksReaming Bit is still used in the coal industry. Because it requires a lot of excavation and exploration, the requirements for drill pipes are high. Today, the editor will tell you what is the working principle and stress analysis of grooved drill pipe? Grooved drill pipe is a spiral transport groove set on the surface layer of the drill pipe. Under the precondition that it is determined...0 Comments 0 Shares 700 Views
- How To Drill Tapered BitPneumatic water well drilling rig blows holes Experiments show that when the gas drill is drilling normally, check the discharge of cuttings and cuttings at the orifice and the footage. When the powder output and the footage are normal, there is no need to lift the drill bit. If only the footage is normal, the drilling tool should be lifted once after a certain footage has been...0 Comments 0 Shares 693 Views
- Safety Failures Used By Dth Drill PipeTop Hammer Drilling Tools must do some preparatory work before construction and run it in order to proceed smoothly. Then let's learn what preparations should be made before the construction of the down-the-hole drilling rig: 1. Before the down-the-hole drilling rig works, it is necessary to carry out a survey of the surrounding environment. There should...0 Comments 0 Shares 674 Views
More Stories